Announcement

Collapse
No announcement yet.

Last ever YKC/Aquila chassis with kit out parts for sale.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Last ever YKC/Aquila chassis with kit out parts for sale.

    OK everybody I am up for a sensible offer for this lot , I would rather it go to someone involved with the club but if no interest then I shall list it on ebay, as I am now desperate for the room in my workshop.

    I have for sale the last YKC/Aquila Julietta/Mille miglia chassis ever made!
    . This a unique opportunity to upgrade an existing Lwb Marina based Roadster or perhaps build a hillclimb/race/road special.
    I would rather sell it as a package but if enough interest I will break it down.
    It consists of the following:-

    1 chassis black poly coated, with all associated bracketry, including pedal box, floor pans, trans tunnel, h/brake plate, de dion tube and trailing arms with panhard rod with bushes all fitted.
    2 x recon rear hubs and bearings to take disc brakes
    2 x new front hubs and bearings
    2 x front ykc coilover struts with springs
    2 x rear coilover shocks with springs
    2 x ykc front tie bars
    2 x new lower track control arms
    1 x ykc modified recon steering rack with rack extenders
    1 x new Master cylinder and new servo
    1 x new 3.92:1 2.0 inj differential
    2 x new complete ykc chrome plated drive shafts and cv joints
    2 x new doors (surface rust) with hinges
    2 x engine bay sides (non louvered)
    2 x engine block mts to suit ford zetec
    2 x engine chassis mts to suit zetec
    1 x sierra s/hand steering column
    1 x s/hand handbrake
    1 x s/hand throttle pedal
    1 x kunifer brake pipe set.
    1 x windscreen frame bolt on type
    1 x s/hand flywheel bellhousing and sandwich plate (zetec to type 9)
    1 x alternator bracket (standard lucas acr to zetec)
    1 x clutch cable and throttle cable
    1 x specially fabricated plenum chamber and throttle body set up.

    £offers/ possible part ex w.h.y.

    There are various other bits and pieces that I haven’t mentioned. I will try to upload some photos, but viewing is welcome by arrangement. I am only selling because we are moving to France next year and I have just bought back one of my old cars. Thanks for looking Steve Himsworth 07966 201106 [email protected]
    Last edited by Steve Himsworth; 26-06-15, 04:35 PM.

  • #2
    Re: Last ever YKC/Aquila chassis with kit out parts for sale.

    Steve, a couple of questions, if you do end up breaking the lot
    1 Do you have the bonnet half's ?
    2 is the differential new as opposed to a recon?
    and finally how much ?
    send a private email if you wish
    YKC 1994 Roadster LWB 3.5 Rover V8

    Comment


    • #3
      Re: Last ever YKC/Aquila chassis with kit out parts for sale.

      Hi Mike, long time no see, No I dont have any bonnet halves left, but not to difficult to make if you can find a suitable piece of 6"dia tube.(i think it was 6" that we used) and does the club have templates for the bonnet halves?
      I will have to check the diff again just to confirm but I`m sure it was part of the original stock, it certainly looks new. I will send you a picture, give me a day or two.
      Regards Steve

      Comment


      • #4
        Re: Last ever YKC/Aquila chassis with kit out parts for sale.

        Now open to sensible offers on this lot, desperate for space in my workshop, if no interest i shall list it on ebay, could be up for p/x w.h.y.

        Comment

        Working...
        X