Announcement

Collapse
No announcement yet.

carb Issues

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • carb Issues

    Bit of a mystery this one folks.

    New carb fitted in June (new old stock) from the carb hospital chappie. Last one he had in the 1275 marina dept! Its a later HS4 but with the waxstat thingmy. Anyway, fitted and colourtuned and idle to midrange fairly spot on and flat out it picks up well and runs cleanly, but seems to run incredibly lean.

    Midrange at about 50, but when putting power in, it is spluttering and misfiring like a bad one! If you ease off things smooth out again as things do if you turn the tap on fully. Today, in an effort to figure it all out, I opened (closed) the choke just when the misfire occurred and I was instantly rewarded with power and smooth running again. So probably a jet issue I think. Engine seems fairly standard with the exception of a 4 branch exhaust linking to a side exiting silencer.

    May use the little programme that is available to aid SU jet selection, but any similar experiences out there guys?

    Scotty

  • #2
    Re: carb Issues

    If it runs better with the choke out I would be looking for manifold gasket leaks and /or leaking servo or servo pipe. Followed by filters and fuel pump and pickup pipe in the tank. Well that's the weekend taken care of.
    Phil

    Comment


    • #3
      Re: carb Issues

      have you checked the tappets - points gap - plugs - ignition timing at 3000 revs ?? should always do this first before even touching the carbs - make sure the carb is free in the dashpot !!

      Comment


      • #4
        Re: carb Issues

        Checked there's oil in the dashpot???

        Comment


        • #5
          Re: carb Issues

          The waxstat unit on the jet is designed to compensate for the air temperature so as the air gets hotter the air density decreases so the waxstat leans off to balance the mixture. Marlin engine bays tend to run hot so possibly whats happening is the mixture is leaning off too much. I would be inclined to get a standard non waxstat jet unit to replace the waxstat.
          Ben Caswell probably not the last word on anything here!!

          Comment


          • #6
            Re: carb Issues

            Conversion kit for waxstat to non wax available:



            Until I read this forum post I never knew that such a thing existed. Google to the rescue! Peter.

            Comment


            • #7
              Re: carb Issues

              Yes indeed Guys, a few weekends tinkering shall now be had. Thanks to all for your replies. I will replace the waxstat, check for induction leaks, although my brakes are without servo.
              Something tells me its jetted wrong, although I never considered fuel pressure. When I fitted the new carb, it ran perfectly and cut out after around 30 secs. On removing the float chamber top, there was no fuel. Primed fine on the starter, cover on then ran for 30 secs etc.

              Pondered for a day then a close examination revealed there was no vent hole on the inlet chamber top at all. This was found after a close exam of the old worn out HS4, which had a 1mm vent hole on side of cast body almost where inlet fitting was. New carb had a strange plastic ball bearing on top, which i drilled clear. This resulted in starting and ok running but is obviously a larger vent than normal. I would have replaced with the old top but this is worn out around the float hinge area.

              Scotty

              Comment


              • #8
                Re: carb Issues

                Also check the needle valves in the float chamber...these are particularly sensitive to dirt/debris.
                Waxstats generally are the work of the devil.
                Marlin Roadster, LWB...1860 B Series + Ford Type 9
                Renault Espace 54mm front calipers, vented discs, cycle wings and adjustable tie-bars.

                Comment


                • #9
                  Re: carb Issues

                  likes machine gun.jpg

                  Originally posted by lil_red_roadster View Post
                  Also check the needle valves in the float chamber...these are particularly sensitive to dirt/debris.
                  Waxstats generally are the work of the devil.

                  Comment


                  • #10
                    Re: carb Issues

                    I was watching an interesting video that was explaining the basic principles of how an SU carburettor works.
                    What happens when you accelerate is explained.
                    The symptoms you describe tend to suggest that the piston assembly is rising too fast when you accelerate, the oil in the dashpot is supposed to slow the rise of the piston to give the engine an extra burst of fuel.
                    You indicate that the problem stopped when you pulled out the choke which has the effect of delivering more fuel.

                    This is the link to the you tube videoa https://www.youtube.com/watch?v=60Bj...3F91CA3FEE0297

                    It's by John Twist from University Motors in America, they specialise in MG's

                    Have a look it may point you in the right direction

                    Comment

                    Working...
                    X