Activity Stream
-
Older Activity
-
Today, 01:07 PMYes, I was surprised how good they seem to be. They will all get a good clean up and repaint. I'm considering adding a reinforcing plate to the top...35 replies | 1144 view(s)
-
Today, 12:12 PMHi Andy. As a separate issue it is good practice to fit a washer on the handbrake clevis pin before fitting the split pin. A liberal smear of...35 replies | 1144 view(s)
-
Today, 11:55 AMAndy, from experience (!) it's worth a careful crack check around the holes on the top and bottom plates, and the shocker attachment plates as well,...35 replies | 1144 view(s)
-
Today, 11:38 AMI pulled the Ubolts and saddles from the read suspension last night... This is how the Marina Ubolts compare to the Escort ones... ...35 replies | 1144 view(s)
-
Yesterday, 08:43 PMI remember that, memory is a funny thing isn’t it.35 replies | 1144 view(s)
-
Yesterday, 04:11 PMOn a slightly different tack. When I took the carpet out I found that the floor board fouls the front leaf spring eye bolt. The last time I was...35 replies | 1144 view(s)
-
Yesterday, 09:31 AMI have the same superflex bushes and yes they are longer than the original so I would probably trim them to be the same length as the plates as the...35 replies | 1144 view(s)
-
23-02-2021, 05:08 PMexcuse me I do not express well in English35 replies | 1144 view(s)
-
23-02-2021, 05:05 PMno thank you35 replies | 1144 view(s)
-
23-02-2021, 03:34 PMI only ask because I have a pair if you need them. Regards Adrian Do you need the lower plates? Adrian35 replies | 1144 view(s)
-
23-02-2021, 01:37 PMI think the plates are used to wrap the rubber to make it stiffer. In what way would they need cutting to fit?35 replies | 1144 view(s)
-
23-02-2021, 12:36 PMdo not cut the SuperFlex?35 replies | 1144 view(s)
-
23-02-2021, 12:17 PMThanks Dave.4 replies | 185 view(s) -
23-02-2021, 12:16 PMDo you need the lower plates? Adrian35 replies | 1144 view(s)
-
23-02-2021, 11:43 AMI don't remember which Pitstop it was but there you are Danny Rgds DC4 replies | 185 view(s)
-
23-02-2021, 10:52 AMSuperflex rear leaves Spring ** version of longer springs improved It must be cut for plates?35 replies | 1144 view(s)
-
23-02-2021, 09:37 AMI am advertising for a club member who is not so well. These were produced in Evesham by two club members some years back. The moulds are good and...4 replies | 185 view(s)
-
23-02-2021, 08:37 AMSold at £2400. Shame it was so late or I would have watched. With the end of lockdown in sight maybe people are in need of fun. Though maybe not this...5 replies | 395 view(s)
-
22-02-2021, 06:55 PMCheers, Danny, just when I am halfway through cutting my LWB hard top down to SWB, and I'm not giving up now! How about pics? Dave4 replies | 185 view(s)
-
22-02-2021, 05:41 PMBoth the SWB and the LWB Roadster hard top moulds are available at very reasonable cost. Please contact danny.nelson@blueyonder.co.uk or...4 replies | 185 view(s)
-
22-02-2021, 12:40 PMShould I keep the montage like in my photos?35 replies | 1144 view(s)
-
22-02-2021, 11:14 AMSome marina's (mine being one of them) didn't have the top location plate. See diagram below. The lowering blocks supplied have a 3° taper to...35 replies | 1144 view(s)
-
22-02-2021, 09:32 AMphotos35 replies | 1144 view(s)
