Click here to sign up  Click here to go to the galleries  Click here to go to the code of conduct  Click here to go to the video page  Click here to go to the SW Meets page

Search:

Type: Posts; User: jason

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    1,297

    Re: Berlinetta headlining.

    I have used high temperature spray adhesive on a foam backed material. that has lasted about 5 years no problem.
  2. Thread: stiff gearbox

    by jason
    Replies
    14
    Views
    1,746

    Re: stiff gearbox

    I am going to have a look this weekend. Does anyone know if the yokes fulcrum pin is one length?
  3. Thread: stiff gearbox

    by jason
    Replies
    14
    Views
    1,746

    Re: stiff gearbox

    Thanks Peter. There is a click at start of travel, so you might well be on to something there. it is a white quadrant as i remember.
  4. Thread: stiff gearbox

    by jason
    Replies
    14
    Views
    1,746

    Re: stiff gearbox

    Thanks for the response folks, the oil was supplied by BGH when the gearbox was purchased so I dont think that will be the issue. Thanks V8 Pete, the gear lever is a little stiff when the engine is...
  5. Thread: stiff gearbox

    by jason
    Replies
    14
    Views
    1,746

    stiff gearbox

    Does anyone have any experience with a type 9 gearbox that is stiff to shift?
    The gearbox is new from BGH and seems to be suffering the same problem as the old box in terms of shifting gears...
  6. Replies
    7
    Views
    1,297

    Re: Berlinetta headlining.

    A local foam supplier suggested thin foam backed material that was used specifically for headlining. Has some elasticity and fitted with high temperature resistant spray adhesive.
    This has not...
  7. Thread: Bike carbs

    by jason
    Replies
    13
    Views
    7,557

    Re: Bike carbs

    Hi Chaps I have some photos for you of the carbs my Berlinetta, I have Ram air foam filters which are easily fitted over the short trumpets. They do not touch the side of the bonnet flaps and have...
  8. Thread: Bike carbs

    by jason
    Replies
    13
    Views
    7,557

    Re: Bike carbs

    I have put kawasaki ZZR 600 carbs on my Berlinetta , this was a kit from Danst engineering. I asked for the carbs to be as horizontal as possible and these fitted the bill. 36mm CV.

    Easy to fit....
  9. Thread: Pinto Manifold

    by jason
    Replies
    20
    Views
    10,168

    Re: Pinto Manifold

    My system has a ear drumming resonance at 2750 rpm + or - a few hundred RPM about 60 -70 mph for my gearing. I seem to remember picking up information when i was training as a mechanic many many...
  10. Thread: Pinto Manifold

    by jason
    Replies
    20
    Views
    10,168

    Re: Pinto Manifold

    That's quite a neat installation Burgoyne 69. thanks for the photos. I will keep trawling the net. The whole exhaust will be coming off soon in an attempt to reduce the resonance and have a freer...
  11. Thread: Pinto Manifold

    by jason
    Replies
    20
    Views
    10,168

    Re: Pinto Manifold

    Thanks folks. the car has the twin down pipe cast manifold already, not sure what it was off. It fits well but i am keen to get the engine breathing more freely and was looking at perhaps fitting the...
  12. Thread: Pinto Manifold

    by jason
    Replies
    20
    Views
    10,168

    Pinto Manifold

    Any one know whats the best fit 4-2-1 exhaust manifold for a 2.1 SOHC sierra Berlinetta ? Capri, Escort RS2000, Cortina?

    I don't want to take a guess and find that it fouls the engine mount or...
Results 1 to 12 of 12