Click here to sign up  Click here to go to the galleries  Click here to go to the code of conduct  Click here to go to the video page  Click here to go to the SW Meets page

Search:

Type: Posts; User: chris_cussen

Page 1 of 21 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    4
    Views
    457

    Re: Handbrake cable question

    Hi Pete
    Unfortunatelyfor you this is what the Marlin build manual says
    NOTE: The cable ends used on the disc braked axle are not possible to obtain when the cable is shortened and Marlin have these...
  2. Replies
    4
    Views
    411

    Re: Ford Clutch Quadrant Options

    Hmm!
    My Cabrio very occasionally lets out a bang and the clutch pedal slips a bit. Afetrwards it all works OK, but I have assumed it is something to do with the quardant slipping a tooth. I have...
  3. Replies
    244
    Views
    82,785

    Sticky: Re: MOC South West monthly meet

    Sorry, out running
  4. Replies
    20
    Views
    1,152

    Re: Dodgy wiring ...

    Loads of inertia switches on eBay
  5. Replies
    20
    Views
    1,152

    Re: Dodgy wiring ...

    Our Mondeo was fine unless the temprature was sub-zero. Then when the ignition was turned on the engine fan would come on and it wouldn't start. By the time any AA home start turned up it was above...
  6. Replies
    7
    Views
    578

    Re: IVA Vin Number

    IVA manual (search online for the latest) states in section 18 Statutory Plates
    7.The Stamped in VIN must be marked on the chassis, frame or other similar structure which is not easily removable,on...
  7. Replies
    7
    Views
    545

    Re: IVA Vin Number

    Mike, my VIN was split over 2 lines which was not considered acceptable :(
  8. Replies
    7
    Views
    545

    Re: IVA Vin Number

    For the standard nuts I bought some rubber nut covers that just slip on.
    On the anti-rollbar where the large nuts is on the end I made a cover from some water pipe insulating foam and covered it in...
  9. Replies
    7
    Views
    578

    Re: IVA Vin Number

    One of my IVA failures was the VIN was on the near(passanger) side and split over two lines.
    The tester commented the rule was stupid as many production cars have the VIN number in other locations,...
  10. Replies
    7
    Views
    545

    Re: IVA Vin Number

    I had the same issue. Mine failed IVA because of this ( and a few other minor issues though it was the first Cabrio to get throught IVA)...
    I bought a set of number/letter stamps and stamped the VIN...
  11. Replies
    20
    Views
    1,926

    Re: Whatever happened to J C sportscars?

    coincidence, it was on page one of the BBC website then I came here.
  12. Replies
    20
    Views
    1,926

    Re: Whatever happened to J C sportscars?

    Sadly Stephen Moore has left us https://www.bbc.co.uk/news/uk-50035065
  13. Re: Tapping / Clunking under load from gearbox, propshaft area of Berly

    Could be propshaft UJ?
    Check for play.
  14. Replies
    13
    Views
    1,124

    Re: 2l DOHC engine removal.

    Distance between floor and the bottom of the beam I use is 2.25metres.
    I put a chain around the beam and use one of these hoists .
  15. Replies
    13
    Views
    1,124

    Re: 2l DOHC engine removal.

    Yes you can leave all the electrics to the lights etc. in place.
    An engine crane would be useful. I dangle the engine from a beam in the garage and push the car back after I have freed the engine...
  16. Replies
    13
    Views
    1,124

    Re: 2l DOHC engine removal.

    Yes. nose stayed in place.
    I don't know if you can take out engine and gearbox in one peice with removing any more. When I installed it as a unit there were no panels fitted, and the gearbox has...
  17. Replies
    13
    Views
    1,124

    Re: 2l DOHC engine removal.

    Hi Stewart. I've done 2l DOHC engine in/out several times. If you are going to only work on the engine I would leave the gearbox in place.
    1. Remove bonnet. You can get better access if you remove...
  18. Replies
    2
    Views
    1,480

    Re: Pitstop 212 LED lights.

    Thanks for that Steve.
    Following the comments after my post about having the indicators placed on the inside and not the outside I did check visually that there was +-80 degrees of coverage from the...
  19. Replies
    37
    Views
    3,160

    Re: Marlin Roadster Registration Advice

    A long time ago in a place not far away (my drive) I built a Spartan Treka. I did invent a VIN for it, CAC-01 (my initials plus a number) My wife wasn't happy when she realised the last in the...
  20. Replies
    37
    Views
    3,160

    Re: Marlin Roadster Registration Advice

    I don't think so, see https://www.gov.uk/vehicle-registration/vehicle-identification-number
    BTW the chassis number has to be stamped on the car and the IVA manual defines how and where (I know...
  21. Thread: Engines

    by chris_cussen
    Replies
    11
    Views
    1,416

    Re: Engines

    Having replaced a DOHC 2.0l on carbs with a Zetec engine I would say that moving a swirl pot and exhaust system are not the major issues.
    This thread details everything I did...
  22. Replies
    5
    Views
    2,043

    Re: Marlin Cabrio - hood seal

    Dunno-but if you find out please share!
  23. Replies
    16
    Views
    2,342

    Re: Cabrio rear bearing noise?

    I'm willing to be shot down in flames but: ignoring XR4is as far as I know the internals of the Serria diff are good for at least 250bhp regardless of the donor vehicle and diff ratio..
    The...
  24. Replies
    16
    Views
    2,342

    Re: Cabrio rear bearing noise?

    I used to get wha wha wha noise when being chased by Mr.Plod :eek:
  25. Replies
    12
    Views
    1,223

    Re: LED rear lights

    Checked the visibilty angles using a protractor. Both indicator and tail can be seen at 80deg from the centreline.
    Steve: The regs made a bit of "light" reading.
Results 1 to 25 of 516
Page 1 of 21 1 2 3 4