Click here to sign up  Click here to go to the galleries  Click here to go to the code of conduct  Click here to go to the video page  Click here to go to the SW Meets page

Search:

Type: Posts; User: duncan

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    193

    Re: Marina B series camshaft swap

    If you are just changing the camshaft then I would use the magnet and dowel system - take the radiator out, remove the rack and front moulding and you will have buckets of room

    Once you have the...
  2. Thread: Coil overs

    by duncan
    Replies
    26
    Views
    1,047

    Re: Coil overs

    If the measure was taken from the vertical instead of the horizontal then the 40 degrees becomes 50 degrees and from that calculator the "motion ratio" becomes 0.696 - which as it is squared means...
  3. Thread: Coil overs

    by duncan
    Replies
    26
    Views
    1,047

    Re: Coil overs

    Excellent!
    I had not realised just how much of an angle the damper sat at

    The 0.584 - "motion ratio" means that the spring moves for 0.584 inches for every inch the wheel moves - and you SQUARE...
  4. Thread: Coil overs

    by duncan
    Replies
    26
    Views
    1,047

    Re: Coil overs

    "Duncan's Dubius Device" - is my electric roadster - Hitachi Forklift motor and Chevy Volt Battery
    ...
  5. Thread: Coil overs

    by duncan
    Replies
    26
    Views
    1,047

    Re: Coil overs

    I am amazed at those spring rates
    My "device" is 800 kg - 900 kg with me in it - and 45% on the front and I am using it on the road/track with 110 lbs/inch on the front -
    my springs are more...
  6. Thread: LED Rear Lights

    by duncan
    Replies
    6
    Views
    455

    Re: LED Rear Lights

    I'm using LED's all round - you need an LED flasher unit to go with them
  7. Replies
    5
    Views
    357

    Re: Roadster 1.3 A series radiator

    Hi
    The mini radiator was enough to cool a 1275 with shall I say dubius airflow mounted sideways in the mini - with the massively better airflow in the Roadster I would expect it not to be an issue
    ...
  8. Replies
    18
    Views
    1,070

    Re: GT6 Based overheating

    These are older motors - the studs should not need to be changed

    In some (most?) newer engines the bolts are actually permanently stretched when you torque the head down and have to be replaced...
  9. Replies
    18
    Views
    1,070

    Re: GT6 Based overheating

    Difficult to see on your photos but the large pipe on the bottom on the expansion tank must be connected to the "suck" side of the water pump -
    or at least must be closer to the suck side than the...
  10. Replies
    18
    Views
    1,070

    Re: GT6 Based overheating

    It is probably not the problem but ensure that the flow through the header tank is the correct direction - I have seen cars where the header tank which is intended to remove air from the water system...
  11. Thread: First Winter

    by duncan
    Replies
    12
    Views
    1,018

    Re: First Winter

    Probably worried about getting too hot - not usually a problem in the UK
  12. Replies
    17
    Views
    1,817

    Re: Propshaft for gearbox swap

    Hi Guys

    There are a couple of things that you need to know

    Propshafts have two UJ's and a sliding joint - you need all three - some gearboxes have the sliding bit as part of the gearbox - it...
  13. Replies
    29
    Views
    5,036

    Re: Was someone looking for a Fiat Twin Cam?

    Hi
    SPV 193 is Phil Butler's Marlin - I believe it has been off the road for about 10 years

    It was a Triumph kit - but it has a live axle from a Ford and a Fiat Twin Cam

    I remember helping to...
  14. Replies
    10
    Views
    1,482

    Re: Fiat Engine Carb upgrade

    Hi
    I would get the carb set by somebody who knows exactly what he is doing on a rolling road - if your "expert" says he does not need one then he is an idiot not an expert

    You can get it sorta...
  15. Replies
    69
    Views
    7,984

    Re: Le Mans and not quite return

    Hi
    Steering racks are simple things - give it a good clean - a visual inspection
    And check that it moves freely from stop to stop

    The most likely failures would be damage to the housing or a...
  16. Thread: buch

    by duncan
    Replies
    12
    Views
    1,511

    Re: buch

    Really?
    As a mini fan from the 70's through the 80's with lots of mini's that was about the only part I didn't have to change!
  17. Replies
    69
    Views
    7,984

    Re: Le Mans and not quite return

    For something like a broken nosecone or even the back wing fiberglass is actually really easy to repair - especially as you have not yet painted it!
  18. Replies
    69
    Views
    7,984

    Re: Le Mans and not quite return

    Thanks - that helps a lot

    Some of the early steering geometry would pull the wheel out of your hand if you got a blowout
    Sounds like the Marina was after they realised

    thanks
  19. Replies
    69
    Views
    7,984

    Re: Le Mans and not quite return

    Hi Adrian

    Can you remember what actually happened?
    Did the tyre blowing pull the car sideways?
    - or did it rip the wheel out of your hands and steer right?

    I'm thinking about the geometry of...
  20. Thread: MOT

    by duncan
    Replies
    73
    Views
    7,066

    Re: MOT

    I have the dampers that came with my car - bought 23 years ago and never actually been finished

    I had assumed that the dampers had bump and droop stops - do they have the stops inside? - just not...
  21. Thread: MOT

    by duncan
    Replies
    73
    Views
    7,066

    Re: MOT

    Bump stop for the front?
    I thought that the front dampers included the bump stop and the droop stop?
  22. Thread: MOT

    by duncan
    Replies
    73
    Views
    7,066

    Re: MOT

    Weather?
    It's cold and wet and horrible - we even had some snow
  23. Thread: MOT

    by duncan
    Replies
    73
    Views
    7,066

    Re: MOT

    That requirement - spare bulbs is what killed the old sealed beam headlamps
    Shame as back then the headlamps with seperate bulbs used to rust something awful
  24. Replies
    11
    Views
    1,713

    Re: Adjustable Tie Rods.

    My tuppence worth on this
    As my car is going to be certified as a "Scratch built" I have to show my certifier that my suspension is fit for purpose (New Zealand)

    Which is NOT that difficult! -...
  25. Replies
    13
    Views
    3,101

    Re: Expansion tank woes.. and a fix!

    That looks like a job for some of those black cable ties - tie the beggar on to it's bracket
Results 1 to 25 of 45
Page 1 of 2 1 2