Click here to sign up  Click here to go to the galleries  Click here to go to the code of conduct  Click here to go to the video page  Click here to go to the SW Meets page

Search:

Type: Posts; User: chris_cussen

Page 1 of 21 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    20
    Views
    811

    Re: Whatever happened to J C sportscars?

    coincidence, it was on page one of the BBC website then I came here.
  2. Replies
    20
    Views
    811

    Re: Whatever happened to J C sportscars?

    Sadly Stephen Moore has left us https://www.bbc.co.uk/news/uk-50035065
  3. Re: Tapping / Clunking under load from gearbox, propshaft area of Berly

    Could be propshaft UJ?
    Check for play.
  4. Replies
    13
    Views
    825

    Re: 2l DOHC engine removal.

    Distance between floor and the bottom of the beam I use is 2.25metres.
    I put a chain around the beam and use one of these hoists .
  5. Replies
    13
    Views
    825

    Re: 2l DOHC engine removal.

    Yes you can leave all the electrics to the lights etc. in place.
    An engine crane would be useful. I dangle the engine from a beam in the garage and push the car back after I have freed the engine...
  6. Replies
    13
    Views
    825

    Re: 2l DOHC engine removal.

    Yes. nose stayed in place.
    I don't know if you can take out engine and gearbox in one peice with removing any more. When I installed it as a unit there were no panels fitted, and the gearbox has...
  7. Replies
    13
    Views
    825

    Re: 2l DOHC engine removal.

    Hi Stewart. I've done 2l DOHC engine in/out several times. If you are going to only work on the engine I would leave the gearbox in place.
    1. Remove bonnet. You can get better access if you remove...
  8. Replies
    2
    Views
    1,106

    Re: Pitstop 212 LED lights.

    Thanks for that Steve.
    Following the comments after my post about having the indicators placed on the inside and not the outside I did check visually that there was +-80 degrees of coverage from the...
  9. Replies
    37
    Views
    2,759

    Re: Marlin Roadster Registration Advice

    A long time ago in a place not far away (my drive) I built a Spartan Treka. I did invent a VIN for it, CAC-01 (my initials plus a number) My wife wasn't happy when she realised the last in the...
  10. Replies
    37
    Views
    2,759

    Re: Marlin Roadster Registration Advice

    I don't think so, see https://www.gov.uk/vehicle-registration/vehicle-identification-number
    BTW the chassis number has to be stamped on the car and the IVA manual defines how and where (I know...
  11. Thread: Engines

    by chris_cussen
    Replies
    11
    Views
    1,156

    Re: Engines

    Having replaced a DOHC 2.0l on carbs with a Zetec engine I would say that moving a swirl pot and exhaust system are not the major issues.
    This thread details everything I did...
  12. Replies
    5
    Views
    1,597

    Re: Marlin Cabrio - hood seal

    Dunno-but if you find out please share!
  13. Replies
    16
    Views
    1,960

    Re: Cabrio rear bearing noise?

    I'm willing to be shot down in flames but: ignoring XR4is as far as I know the internals of the Serria diff are good for at least 250bhp regardless of the donor vehicle and diff ratio..
    The...
  14. Replies
    16
    Views
    1,960

    Re: Cabrio rear bearing noise?

    I used to get wha wha wha noise when being chased by Mr.Plod :eek:
  15. Replies
    12
    Views
    1,095

    Re: LED rear lights

    Checked the visibilty angles using a protractor. Both indicator and tail can be seen at 80deg from the centreline.
    Steve: The regs made a bit of "light" reading.
  16. Replies
    12
    Views
    1,095

    Re: LED rear lights

    It went through IVA with the lights that way round, as in my first photo. :confused:

    The recessed hole is symetrical so I only need to remove the lights and rotate them 180 degrees.
    But the...
  17. Re: Raceline water rail, Zetec engine and overheating.

    Yes its all sorted, the hole did the trick.
    The raceline water rail is machined so that is is nearly impossible to put the stat in the wrong way round.
  18. Raceline water rail, Zetec engine and overheating.

    My experiment to determine if the fan was coming on when the engine was getting hot was documented in another thread Got-puzzled continued with the engine getting hotter.
    I have a Zetec engine with...
  19. Replies
    12
    Views
    1,095

    Re: LED rear lights

    Yes, sealed units, if they break the only solutions is complete replacement. But LEDS seem very reliable.
  20. Replies
    12
    Views
    1,095

    LED rear lights

    Having seen the LED rear lights post https://www.marlinownersclub.com/forum/showthread.php?8025-LED-Rear-Lights and never being happy with the gastly rubberlite ones on my cabrio
    11017
    I decided it...
  21. Replies
    7
    Views
    1,014

    Re: Roadster with Holbay Hunter engine

    That gave me butterflies, the ebay advert offers "3 to 36 Moths Warranty Available with all our cars."
  22. Replies
    6
    Views
    938

    Re: LED Rear Lights

    I've just brought them. When fitted I'll add some pictures and information.
  23. Replies
    12
    Views
    1,393

    Re: Speedometer Access

    Sorry, can't help directly. I've got a plain ally dash covered in black leathercloth. There is a dash capping which on my car is screwed at either end, the screw heads aren't visible unless the door...
  24. Replies
    8
    Views
    972

    Re: Got puzzled

    Can't remeber exactly how I did it but I used a combination of diodes to control the reversing lamp so that it would only come on when the ignition and lights were on. Initial attempt meant that if...
  25. Replies
    8
    Views
    972

    Re: Got puzzled

    Thanks for the suggestions. I've got an infra-red temperature ray gun gadget which I tried out after the LED attempt, It showed the temperature of the water rail as somewhere between 70C and 90C...
Results 1 to 25 of 506
Page 1 of 21 1 2 3 4