Announcement

Collapse
No announcement yet.

New Gearbox lever thread - revised

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #61
    Re: New Gearbox lever thread - revised

    Adrian, that is looking good, when are you getting it in the car?
    May use that idea myself as I am way behind you.

    Comment


    • #62
      Re: New Gearbox lever thread - revised

      A beautiful job . Much envy.

      Comment


      • #63
        Re: New Gearbox lever thread - revised

        Originally posted by meverett View Post
        Adrian, that is looking good, when are you getting it in the car?
        May use that idea myself as I am way behind you.
        Tonight hopefully and will take a picture to show fitment.

        Forgot to mention, have sussed reverse detent, made it a sping plate instead, utilising the original plate and spring. Just enough pressure to stop me pushing it in reverse. No more lifting. see pic below :

        20171016_094359.jpg

        Comment


        • #64
          Re: New Gearbox lever thread - revised

          Originally posted by HairyDave View Post
          A beautiful job . Much envy.
          Thank you, oh and it does work (amazingly)

          Adrian

          Comment


          • #65
            Re: New Gearbox lever thread - revised

            I presume you have removed the reverse 'gate'?

            Comment


            • #66
              Re: New Gearbox lever thread - revised

              Originally posted by stevejgreen View Post
              I presume you have removed the reverse 'gate'?
              Hi Steve

              Nope used it.

              When you push over the gear stick it pushes against the reverse gate and the spring and pushes the plate out.

              When you take it out of gear the spring pushes the gate back.

              There is enough force in the spring for it to tell me that I am trying to go into reverse.

              regards

              Adrian
              Last edited by listerjp2; 16-10-17, 09:15 AM.

              Comment


              • #67
                Re: New Gearbox lever thread - revised

                Lovely

                Comment


                • #68
                  Re: New Gearbox lever thread - revised

                  Seconded! It's a shame that the engineering brains here aren't running the country.

                  Comment


                  • #69
                    Re: New Gearbox lever thread - revised

                    Originally posted by HairyDave View Post
                    Seconded! It's a shame that the engineering brains here aren't running the country.
                    I agree.

                    Adrian

                    Comment


                    • #70
                      Re: New Gearbox lever thread - revised

                      Originally posted by listerjp2 View Post
                      OK guys here it is.

                      Note: Only for those who don't mind having their engineering work on show as this sits above the tunnel but for me, I love it.

                      Parts required;

                      1 x 12mm male to female studded rose joint - £6.50
                      2 x 12mm clevis fork - £3.70
                      2 x 12mm clevis eye - £6.56
                      2 x 12mm clevis pin with clip - £1.00
                      3 x 12mm nuts - £1.44
                      1 x 12mm hub bolt - £1.00
                      1 x 12mm studding - £4.89
                      1 x 3" x 1" bar (steel or otherwise ) - found in metal bits
                      1 x gaff piece of 4" x 4" steel plate

                      TOTAL £25.09

                      Hopefully the picture says it all.

                      If not ask and I will describe.

                      Now to be honest without my mate doing all the lathe and boring work It would have taken more than the weekend.

                      Adrian

                      [ATTACH]9212[/ATTACH]
                      Forget to add naff welding but thank god its only one bit.

                      As it will be the only piece and will be masked by a carpet, I'm not to worried.

                      I will give it a coat of paint in the final fit.

                      Regards

                      Adrian

                      Comment


                      • #71
                        Re: New Gearbox lever thread - revised

                        Proper Job!!!!!!!!!!!!!!!

                        Comment


                        • #72
                          Re: New Gearbox lever thread - revised

                          Well done that man !

                          Comment


                          • #73
                            Re: New Gearbox lever thread - revised

                            Originally posted by listerjp2 View Post
                            Forget to add naff welding but thank god its only one bit.

                            As it will be the only piece and will be masked by a carpet, I'm not to worried.

                            I will give it a coat of paint in the final fit.

                            Regards

                            Adrian
                            Last part of the jigsaw.

                            First

                            20171016_153017.jpg

                            Second

                            20171016_153054.jpg

                            Third

                            20171016_152922.jpg

                            Fourth

                            20171016_153204.jpg

                            And reverse

                            20171016_152922.jpg

                            And the reverse gate works well

                            Adrian

                            Comment


                            • #74
                              Re: New Gearbox lever thread - revised

                              and hopefully a you tube video



                              Adrian

                              Comment


                              • #75
                                Re: New Gearbox lever thread - revised

                                Adrian

                                Looks like a nicely engineered solution.

                                Just a thought - could you turn your 4" square plate upside down to lose the rose joint under the transmission tunnel and make it easier and neater to carpet over? - just means making an extra hole in your plate.

                                Comment

                                Working...
                                X